DIY - Marble Tray

This post is sponsored by The Home Depot.

The countdown is on! Are you done with your holiday décor? How about that shopping list?

I'm about halfway down my gift list, and this cute DIY marble tray that I'm sharing with you today is another item I need to check off my list!

Have you seen those beautiful marble trays in most home stores? 

Well, you can create your very own marble tray for a fraction of what you pay for one of those.

I crated two little trays out of a marble tile set that I got at Home Depot for only eight dollars.
Yep. That would be the cost of your two marble trays, if you happen to have two sets of drawer handles and a drill bit to open the holes in the marble.

Well, you know me, I went a bit further with the details. I also added a wooden base out of scrap wood I had in my stash. I added this extra touch because I think the trays look much better with that wooden line underneath the marble. You don't have to do it, but just in case, let me show you how it was done.

*This post contains affiliate links for your convenience. Click here to read my full disclosure policy.

The materials you'll need for two trays: 

• 1 set (2) - Jeffrey Court Carrara 6 In. x 12 In. honed marble tile 
• 2 sets of drawer handles ( I used two vintage sets)
• Drill
• Bosch 3/16" carbide tipped drill bit

Optional Wooden Base:

• 6' - 1/4 in. x 1-1/2 in. solid pine lattice 
• Miter box and saw
• Super glue
• Clear bumpers
• Clamps

Directions:

These gorgeous vintage drawer handles might be another reason why I tackled this project. I've been wanting to use those wooden pulls for ever! I got them from an online store that was going out of business and they were only a couple bucks each.

1. MARK THE LOCATION TO INSTALL THE DRAWER HANDLES

I made a template out of cardboard paper - same width as the tile, 6". Folded it in half, then in quarters and voila, the template was done.

Note: I added painters tape as a precaution for any chipping that might occur. However, this is not a necessity if you use the Bosch Carbide drill bits I used.
It's also a good idea to do a drilling test on a spare piece of the natural stone if you happen to have it.

I used the Bosch Natural Stone carbide tipped drill bits and they produced neat and clean holes. No water required, they went through the marble like butter.
The set comes with four bits, 1/8", 3/16", 1/4" & 5/16".
They're specially design or use in natural stone tile, slate, granite and specialty tile.

| Bosch Carbide Tipped Drill Bit Set |

2. DRILL 3/16" HOLES FOR THE HANDLES

Using a drill and a Bosch 3/16" Natural Stone Tile bit, drill the holes in the designated spots.

It goes fast and the results are awesome!

| RIDGID 18-Volt Hammer Drill  |

4. INSTALL THE HANDLES

Install the handles with the hardware that comes with them. Don't over tighten them.

You can stop here, you just created a set of beautiful marble trays!

5. ADD A WOODEN BASE

For the base I used pine lattice. Using a miter box and saw I mitered those corners.
After sanding them smooth, the wooden pieces were stained.

| Miter box and saw | Varathane Wood Stain |

Once dry, they were sanded again and a light coat of poly was applied before attaching them to the underside of the marble tray.

Super glue was used to bond both surfaces together. Clamps held them together while the glue dried.

The final step was to add clear bumper feet to protect the surfaces the tray is going to be placed on.

I brought the one with the wooden handles to my bathroom for a photoshoot.

It goes perfectly with all the other wooden tones I have there, in the bathroom.

I love it so much, that now I don't want to give it away!! 🤦‍♀️

I bet you've been through this same situation. You find/create something for someone, but you really want to keep it for yourself!

Well, I still have a few days to decide. 🤔
The other tray got a more modern style. The handles and base were spray painted gold. I love it too.

Well guys, I hope I have inspire you to create your very own marble trays! Which one is your favorite, walnut or gold?




I acknowledge that The Home Depot is partnering with me to participate in the promotional program described above (the “Program”). As a part of the Program, I am receiving compensation in the form of products and services, for the purpose of promoting The Home Depot. All expressed opinions and experiences are my own words. My post complies with the Word Of Mouth Marketing Association (WOMMA) Ethics Code and applicable Federal Trade Commission guidelines.

*This post contains affiliate links.

Enjoy what you read today? Enter your email address below to subscribe to Remodelando la Casa:


Delivered by FeedBurner